MELLES GRIOT 640nm 56CRH/S2832 LASER HEAD & CONTROLLER 56CLC100-074 NEW MATCHED

Description

BRAND NEW
MELLES GRIOT 56CRH/S2832 LASER HEAD & CONTROLLER 56CLC100-074 NEW MATCHED SERIAL NUMBERS
640 nm RED LASER
PERFECT CONDITION - COMPLETE MATCHED ASSY
INCLUDES THE INTERCONNECT CABLES SHOWN
SHIPS FREE IN CONT. USA - ELSEWHERE SHIPS ACTUAL USPS COST - NO ADDITIONAL FEES ADDED.
TECHNICAL DETAIL:
Melles Griot Part Number: 56CRH/S2832 (Document # L99000-215-01-Rev G)  (REFERENCE ONLY) 1. DIODE LASER SYSTEM INCLUDING:  LASER HEAD (SHOWN), CABLE, AND CONTROLLER. 2. WAVELENGTH:  633 to 641 nm 3. OUTPUT POWER: 13.5 to 16.5 mW 4. BEAM QUALITY (M^2) < 1.5 5. BEAM DIAMETER (VERTICAL & HORIZONTAL): 1150 + 200 µm 6. BEAM WAIST LOCATION (X-AXIS & Y-AXIS): 0 + 1000 mm 7. WARM UP PERIOD: < 5 minutes
Wavelength (nm): 633 to 641 Power, Output (mW): 13.5 to 16.5 Warm-up period to spec performance (minutes): < 5 Beam quality, x-axis (M^2): < 1.5 Beam quality, y-axis (M^2): < 1.5 Beam waist location, x-axis (mm):  (Note: with respect to front of laser) 0 + 1000 Beam waist location, y-axis (mm):  (Note: with respect to front of laser) 0 + 1000 Beam Diameter (at 1/e^2)  Measurement method: ModeMaster Vertical Waist (µm): 1150 + 200 Horizontal Waist (µm): 1150 + 200 Circularity (far Field %): >95 Beam Divergence (Full angle at 1/e^2 diameter)  Vertical (mrad): <1 Horizontal (mrad): <1 Beam Centration (mm):  (Note: with respect to center of laser aperture) + 1 Boresight (mrad):  (Note: with respect to laser baseplate) + 5 Transverse Mode: Single Longitudinal Mode: Multiple Polarization  Orientation : Any Reference Plane: Baseplate Ratio: Any  Beam pointing at constant temperature  Beam Deviation (µrad): < 20 Temperature (◦C): Constant +1 Time (hrs): <8 Beam pointing vs. Temperature  Beam Deviation (µrad/◦C), (Note: Maximum change of 5 ◦C/hour):   x-axis <6; y-axis<10 Power Stability  Stability (%): < + 2 Time (hours): < 8 Frequency Range (Hz): Dc to 20 Amplitude Noise, Optical  RMS (%): <1 Frequency Range:  20 Hz to 2 MHz
Input: Vdc Voltage (Vdc): 4.75 to 5.50 Power (W) < 30
System Configuration Mechanical configuration: Per MG P/N:56CRH/S2832OM                                             Description: Outline & Mounting, 56CRH/S2832  Laser Head: (Specification Removed) Cable length, laser to controller (inch): 25+1 J4 Jumper Installed:  No Mechanical Shutter: No Laser Controller: (Specification Removed) DC Power Supply: Customer Operator’s Manual:  One time via email Shipping Packaging: MG P/N: B2856 Description: Packaging Assy, 56CRH Software/Firmware  Firmware: MG P/N:L43000-157-01 Rev 4.1b Description: Firmware, Univ Cont User Interface Software: None EEPROM Configuration: SET:BAND=1 (Low Bandwidth Mode) KS = 1 Auto-start: Yes Auto-restart: Yes Interlock turn-off delay: Std Keyswitch to be left in the OFF position RS-232 will be the only means of turning laser on OFF_KEY signal will be used to prevent laser from turning on when customer system interlock is open Ramp-time, current:0 sec Environmental Specifications Cooling, Laser: conductive Cooling, controller: convective Temperature, Operating (◦C): +10 to +40 Temperature, Storage (◦C): -20 to +60 Relative Humidity, non-condensing (%): < 95 Mounting orientation: Any Shock, non-operating: <25g, <11 msec Vibration, operating (g, ms): <0.3g, 5 to 500 Hz; Sinusoid, 0.25 octave per minute Vibration, non-operating (g, ms): <3.0 g, 5 to 500 Hz; Sinusoid, 0.25 octave per minute Altitude (m): 0 to 3000
Miscellaneous Specifications Packaging Testing Requirements: ISTA Procedure 2A Statutory Requirements: None Regulatory Requirements Laser Safety:  Component; US, FDA, CDHR: 21 CFR 1040.10; EU: IEC 60825-1:2007. Accession Number, US, FDA: 1220063-000 Electrical Safety: None EMC:  None Third Party Test Mark:  None Laser Classification: 3B Directives: EU Directive 2011/65/EU+ Amendment         (European RoHS); EU Directive 2012/19/EU (WEEE)